We posted this short on the Wolf YouTube channel on November 11, 2026. It starts the way a lot of our calls start: garage door won’t open. Here’s why. The camera points up at the bar over the door, and there it is. One torsion spring has snapped clean through.
The whole repair fits in under half a minute of video. In the garage it takes longer, because every step is about controlling the energy stored in those coils. Below is each step from the video and the reason behind it.
The problem: a snapped torsion spring
Torsion springs sit on a steel shaft above the door. They are wound tight, and that stored twist is what lifts the door. The opener only steers it. When a spring breaks, the door is suddenly at its full weight, and most openers can’t lift that. That is why the door stays shut even though the motor runs.
In the video, the break is easy to see: a gap in the coil, circled on screen. If your door is acting the same way, stop using the opener and keep everyone out from under the door. Our first-hour checklist for a broken spring covers what to do while you wait.
The repair, step by step

Step 1: Unwind and remove the old spring
First, we safely unwind it and take it off. A snapped spring doesn’t mean the tension is gone. The other spring is still loaded, so the coils are let down a quarter turn at a time with winding bars, never by loosening a screw and letting go. Only then do the old springs come off the shaft.
Step 2: Fit a new pair of American-made springs
The voiceover says it plainly: new American-made springs go on the shaft. The label on screen names the maker, American Springs. Note the plural. Both springs get replaced, not just the broken one, so the pair starts out even. If you want to know why we are particular about where our springs come from, we wrote about it in American-made garage door springs.
Step 3: Bolt the center bracket tight
The center bracket anchors the stationary end of the springs to the wall above the door. Every bit of twist we put into the springs pushes against that bracket, so it is bolted down tight before any winding starts.
Step 4: Wind to the exact number of turns
Then we wind them to the exact turns. The right count depends on the door: its height, its weight, and the size of the cable drums. Too few turns and the door feels heavy and strains the opener. Too many and it wants to fly up. There is no guessing here.
Step 5: Lock the set screws down
Once the springs are wound, the set screws on each winding cone are tightened onto the shaft. That is what holds all that tension in place. A loose set screw is how a freshly wound spring slips.
The result: a balanced door that lifts smoothly
The short ends on the door rising smoothly, with the line balance smooth, done right. Balance is the test that matters. A door with correctly wound springs feels light by hand and moves without jerking, and the opener goes back to steering instead of lifting.
The video shows the order of the work, not instructions. A wound torsion spring holds enough force to break bones if a bar slips. Unwinding and winding is a job for someone with the right bars and a lot of practice.
Broken spring in Huntington Beach or Orange County?
We handle torsion spring replacement from our Huntington Beach and Santa Ana offices, across Orange County. Not sure what kind of springs your door has? See torsion vs. extension springs, or read about our wider garage door spring repair service. For another spring job on video, see this broken torsion spring in Aliso Viejo.
Call or text (657) 845-8991. We answer 24/7. Tell us the door won’t open and whether the car is inside, and we will take it from there. Rather type it out? Send us a text.
Need it fixed?
Garage Door Torsion Spring Replacement across Huntington Beach and Orange County
A 5.0-star Google rating and a Huntington Beach team that answers 24/7.
Frequently asked questions
What does a broken torsion spring look like?
Look at the bar above the closed door. A broken torsion spring shows a gap of a few inches in the coil. Other signs: the opener runs but the door barely moves, or the door feels far heavier than usual when you try to lift it.
Can I still open my garage door with a broken spring?
It’s best not to. The opener isn’t built to lift the full weight of the door, and forcing it can damage the opener or pull a cable off its drum. Leave the door closed and call or text us.
Do you replace both springs if only one broke?
On a two-spring door, yes. In the video both springs go on new. A matched pair keeps the door balanced, and the older spring has been through the same cycles as the one that broke.
Why does winding to the exact turns matter?
The turns set the balance. Too few and the door is heavy and hard on the opener. Too many and it lifts too hard. The count depends on the door’s height, weight and drum size.
Is it safe to replace a torsion spring myself?
We don’t recommend it. Wound springs store a lot of force, and most injuries happen while unwinding or winding. Our short shows the steps so you know what a proper repair looks like, not as a DIY guide.



